Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateTherma-Tru Door Installation in North Las Vegas: What to Know First
We install Therma-Tru doors in North Las Vegas as an independent Therma-Tru service provider, and most entry and patio door jobs are finished in a single visit once the door is on site. A standard entry door installation runs roughly $1,200 to $3,400 depending on the series, the opening, and whether the frame is being rebuilt. We quote on paper, line by line, before any work starts. This page is for homeowners who already own a Therma-Tru door or have picked one out and want it set true by people who work on them every week. Call (833) 734-5506 and a live person will answer.

How Therma-Tru Products Fail – and How We Fix Them
Therma-Tru builds a good door. What fails in North Las Vegas is rarely the slab itself. It’s the setting, the seal, and the parts around it. Here are the five we see most.
- Sagging and rubbing on Fiber-Classic and Smooth-Star entry doors. On a door that faces west into the afternoon sun, the slab takes on heat all day and the hinge-side jamb moves with it. By July the door catches at the top corner and the deadbolt won’t throw clean. The cause is a frame that wasn’t shimmed and anchored for our temperature swing, not a bad hinge. We reset the frame, re-shim at the hinges, and confirm the reveal is even before we touch the lock.
- Water infiltration at the sill on Therma-Tru patio and French doors. Monsoon rain driven sideways finds a sill pan that was installed flat or skipped entirely during a previous replacement. You’ll see staining on the interior threshold or a soft spot in the flooring six inches inside the door. We pull the door, build a proper sloped sill pan with end dams, and reset it. No amount of caulk on the outside fixes a sill that drains the wrong way.
- Warped or delaminating slabs on older Fiber-Classic doors. Therma-Tru has revised its fiberglass skin and core construction over the years, and doors from earlier production runs in full sun can cup at the edges. Once a slab has cupped past a quarter inch it will not come back, and no adjustment holds it. We measure it and tell you straight whether it’s a hardware fix or a replacement slab.
- Failed weatherstrip and sweep at the bottom rail. The kerf-mounted weatherstrip on Therma-Tru doors compresses and hardens faster in our dry air than most homeowners expect, usually within a handful of summers. A door that whistles or lets in dust at the bottom is almost always this, not the door being “loose.” We replace with the correct kerf profile rather than a peel-and-stick strip that fails by fall.
- Multipoint lock and handle-set misalignment on Therma-Tru entry systems. When a multipoint lock hangs up, the instinct is to force it or swap the handle set. Nine times out of ten the door has shifted in its opening and the lock is doing exactly what it should. We diagnose the door first. A new handle set on a door that’s out of square just breaks the new handle set.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our Therma-Tru Door Installation Process
- 1
The call. A live person answers, day or night. We ask what the door is doing, which Therma-Tru line it is if you know, and roughly how old it is. That tells us what to bring.
- 2
Measure twice, on site. Our technicians measure the rough opening and the existing frame at multiple points. On a replacement we check plumb, level, and square of the opening itself, because a new door set into a racked opening will fail the same way the old one did.
- 3
The parts decision, in writing. We quote OEM Therma-Tru hardware and a quality aftermarket option side by side on paper. OEM keeps your warranty intact and fits the door’s prep exactly. Aftermarket can save money on a door that’s out of warranty. You see both and you choose.
- 4
The install. Old door out, opening cleaned and inspected for rot or water damage, sill pan and flashing done correctly, new door set, shimmed, and anchored. Sealed at the exterior with the right material for stucco, which is most of what we’re setting into in North Las Vegas.
- 5
The test. We open and close the door through its full swing, check the reveal top to bottom, throw the lock and the deadbolt, and run water at the exterior threshold while we watch the inside. If it doesn’t pass, we don’t call it done.
- 6
The paperwork before we leave. Both warranty layers registered in writing, durations stated, and your 90-Day Done Right Promise on the workmanship. No fine print and no arguing later.
What Therma-Tru Door Installation Costs in North Las Vegas
These are real ranges for Therma-Tru work in the North Las Vegas market. Your exact number depends on the door, the opening, and what we find behind the old frame.
| Job | Typical Range |
|---|---|
| Therma-Tru entry door installation, standard opening | $1,200 – $2,400 |
| Entry door installation with frame rebuild or repair | $1,800 – $3,400 |
| Therma-Tru French or double door installation | $2,600 – $5,200 |
| Patio / sliding door installation | $2,200 – $4,800 |
| Hardware, weatherstrip, and sweep replacement only | $180 – $450 |
What moves the price: the Therma-Tru series you chose, glass options, whether the rough opening needs work, and whether we’re setting into stucco or block. We also carry a standing $50 off any repair over $250, an $89 seasonal tune-up, and a permanent 5% discount for seniors and veterans. Call (833) 734-5506 for a free estimate. It’s a square deal and you’ll see it on paper before we lift a tool.
See the difference
Before
After
Before
After
Before
AfterWhy North Las Vegas Homeowners Call TruePane Windows & Doors North Las Vegas for Therma-Tru Work
We’ve proudly served local communities for over 42 years, and we plan to be here in thirty more. That’s why the 90-Day Done Right Promise exists: if it’s not done right, we make it right, no paperwork and no arguing. The Keystone Standard means both manufacturer warranty layers get registered in writing before the truck leaves your driveway, with durations stated. Our technicians have up to 18 years of experience, they’re background-checked and uniformed, and they work in your home the way they’d work in their own mother’s. We’re an authorized installer for more than a dozen manufacturer lines, so if your Therma-Tru door turns out not to be the right answer for an opening, we can quote PGT, CGI, CWS, or ES Windows side by side. Call (833) 734-5506 and a live person will pick up.
FAQs
No, as long as the door is installed to Therma-Tru’s published requirements and the warranty is registered. The manufacturer warranty covers the door and its components; our 90-Day Done Right Promise covers the installation workmanship. We register both layers in writing before we leave and hand you the durations in black and white.
We quote both on paper and let you decide. OEM hardware keeps the door’s factory warranty clean and fits the factory prep exactly, which matters most on multipoint locks and kerf weatherstrip. Aftermarket makes sense on an older door that’s already out of warranty. We don’t swap in cheap parts and call them OEM.
Often just the door. On a Therma-Tru replacement where the existing frame is plumb and sound, we set the new slab or prehung unit into it. If the frame has moved, flared at the sill, or taken water, the frame has to be addressed or the new door will fail the same way. We tell you which one you’re looking at on the estimate.
Most entry doors are done in a single visit. French and double doors or a job with frame repair can run longer, and we’ll tell you the honest window up front. Heat is a real factor here in summer, so we schedule the work to give the sealant time to cure correctly.
Repair if the door is square, the slab is sound, and the problem is hardware, weatherstrip, or adjustment. Replace if the slab has cupped or delaminated, or if the frame has taken water. We measure and tell you which side of that line you’re on. Call (833) 734-5506 for a free estimate and an honest answer.
Call Us for Your Therma-Tru Door
If your Therma-Tru door is sagging, leaking, or you’ve picked out a new one and need it set true, call TruePane Windows & Doors North Las Vegas at (833) 734-5506 for a free estimate. We’ll measure every opening twice, quote manufacturer lines side by side on paper, and register both warranty layers before we leave. If the pane is not true, the job is not done.
Written by the team at TruePane Windows & Doors North Las Vegas, serving North Las Vegas and nearby areas.